Browsing by Subject "Shear bond strength"

Now showing 1 - 3 of 3
  • Thumbnail Image
    Publication
    Open Access
    A comparison of the shear bond strength of a resin cement and two orthodontic resin adhesive systems
    (E.H Angle Education and Research, Inc., 2005-01-01) Vicente, Ascensión; Bravo, Luis Alberto; Romero Maroto, Martín; Ortiz Ruiz, Antonio José; Canteras Jordana, Manuel; Dermatología, Estomatología, Radiología y Medicina Física
    The object of this study was to compare the shear bond strength and the quantity of adhesive remaining on the tooth after the debonding of brackets bonded with two light-cured orthodontic resin adhesive systems (Transbond XT and Light-Bond) and a dual-cured resin cement (RelyX Unicem). Seventy-five premolars were divided into three groups. In each group, brackets were bonded with one of the adhesives according to the manufacturer's instructions. Shear bond strength was measured using a universal test machine at a crosshead speed of one mm/min, and adhesive remnant was quantified using image analysis equipment. Our results showed that the resin cement produced significantly lower bond strength than the two orthodontic resin adhesive systems. It was also observed that the bond strength produced by Light-Bond was significantly greater than that of Transbond XT. RelyX left significantly less remnant adhesive than Transbond XT and Light-Bond. Between the two orthodontic systems, Light-Bond left significantly less adhesive on the tooth than Transbond XT.
  • Thumbnail Image
    Publication
    Open Access
    Influence of fluoride varnish application on enamel adhesion of a universal adhesive
    (Quintessence Publishing, 2021-01) Ortiz Ruiz, Antonio José; Martínez Marco, Francisco José; Pérez Silva, Amparo; Serna Muñoz, Clara; Cabello, Inmaculada; Banerjee, Avijit; Dermatología, Estomatología, Radiología y Medicina Física
    Purpose: To study the effect of the varnish type, application time and surface polishing on the shear bond strength (SBS) of a universal adhesive in healthy and demineralized bovine enamel. Materials and Methods: 432 bovine primary central incisors were assigned to 18 groups according to enamel mineralization [healthy and demineralized], topical varnish [Clinpro White Varnish (CWV; 3M Oral Care) and Profluorid (PFV, Voco)], remineralization time [24 h or 21 days] and polishing or not of the enamel surface. Adhesion was tested using Futurabond M (Voco)+ and GrandioSO (Voco). Sheer bond strength (SBS) was measured and the fracture mode studied. The statistical analysis was performed using two-way ANOVA, Tukey's test, and Pearson's chi-squared test. Results: In healthy bovine enamel, CWV reduced SBS at 24 h and 21 days; polishing significantly improved SBS. PFV increased SBS in healthy enamel at 21 days and demineralized enamel at 24 h and 21 days; polishing had no effect on SBS. The application time and polishing of the enamel surface affected the behavior of varnishes with respect to SBS. There was a correlation between the type of fracture and the degree of mineralization as well as the timepoint of varnish application. Conclusions: Remineralization of demineralized enamel with fluoride varnishes permits the recovery of the bond strength obtained in healthy enamel. Of the two varnishes studied, PFV had the highest SBS and more uniform behavior, regardless of the application timepoint, degree of mineralization, and surface treatment of the enamel.
  • Thumbnail Image
    Publication
    Embargo
    Water and saliva contamination effect on shear bond strength of brackets bonded with a moisture-tolerant light cure system
    (EH Angle Education and Research Foundation, Inc., 2009-01) Vicente Hernández, Ascensión; Mena, Ana; Ortiz Ruiz, Antonio José; Bravo González, Luis Alberto; Dermatología, Estomatología, Radiología y Medicina Física
    Objective: To evaluate the effects of water and saliva contamination on shear bond strength of brackets bonded with a moisture-tolerant light cure system. Materials and Methods: Brackets were bonded to 240 bovine lower incisors divided into 12 groups. Four bonding procedures were evaluated, including (1) TSEP/Transbond XT, (2) TMIP/ Transbond XT, (3) TSEP/Transbond PLUS, and (4) TMIP/Transbond PLUS, each under three different bonding conditions: without contamination, with water contamination, and with saliva contamination. Shear bond strength was measured with a universal testing machine. The adhesive remnant on the teeth was quantified with the use of image analyzing equipment. Results: Without contamination, bond strengths for the four procedures were similar (P > .05). TSEP/Tranbond PLUS and TMIP/Transbond PLUS left significantly less adhesive on the teeth after debonding than TSEP/Transbond XT and TMIP/Transbond XT (P < .008). Bond strength and adhesive remaining for TMIP/Transbond XT contaminated with water or saliva showed significantly worse performance than the other procedures evaluated (P < .008). Contamination (with water or saliva) did not affect either bond strength or adhesive remaining on the teeth for TSEP/ Transbond XT, TSEP/Transbond PLUS, or TMIP/Transbond PLUS (P > .017), although for TMIP/ Transbond XT, both variables showed significant reductions after contamination (P < .017). Conclusion: TSEP/Transbond PLUS, TMIP/Transbond PLUS, and TSEP/Transbond XT showed greater tolerance to wet conditions than was shown by TMIP/Transbond XT.